Login

SG-LightTech

Hi,

I need the fixture chart for the Fos Technolgies Pixelblade 7
what is possible 12Ch Basic 15Ch Standard 39Ch Extended ?
This saturday i have 6 of these pixelblades 7

https://www.fos-lighting.eu/uploads/prod...2_1_19.pdf

Kind regards

Glenn Serneels

***WesleyHouben*** · 16-04-2018, 01:33 PM

(15-04-2018, 07:37 PM)SG-LightTech Wrote: Hi,

I need the fixture chart for the Fos Technolgies Pixelblade 7
what is possible 12Ch Basic 15Ch Standard 39Ch Extended ?
This saturday i have 6 of these pixelblades 7

https://www.fos-lighting.eu/uploads/prod...2_1_19.pdf

Kind regards

Glenn Serneels

Hey Glenn,

So i went ahead and made all 3 possible modes for you (see attached file).
All modes are present however they come with a note. for the 39ch. mode
you have to patch the 39ch. mode followed by 7, RGBW generic LED fixtures.
The Chimp doesnt support multiparameter fixtures. You'll need a work around.
patch 6 x 39ch. pixelblade 7's. then patch 6 x 7 = 42 RGBW fixtures. assuming you
want your function channel go ahead and patch 6 x the pixelblade 39ch. function fixture.
now patching comes down to correct selection order. In order to patch all fixtures at once
you need to do as followed.

for example
Pixelblade 7 39ch. mode FIX ID: 101 thru 106
RGBW LED FIX ID: 401 thru 442
Pixelblade 7 39ch. function FIX ID: 111 thru 116

this is your selection order syntax.
(1st fixture 101 + 401 -> 407 + 111) + (2nd fixture 102 + 408 ->414 + 112) +
(3rd fixture 103 + 414 -> 421 + 113) + and so on and so on.

after doing this for all 6 fixtures hit set and set your start adres. then everything should be
running.

SG-LightTech · 16-04-2018, 10:41 PM

(16-04-2018, 01:33 PM)WesleyHouben Wrote:
(15-04-2018, 07:37 PM)SG-LightTech Wrote: Hi,

I need the fixture chart for the Fos Technolgies Pixelblade 7
what is possible 12Ch Basic 15Ch Standard 39Ch Extended ?
This saturday i have 6 of these pixelblades 7

https://www.fos-lighting.eu/uploads/prod...2_1_19.pdf

Kind regards

Glenn Serneels
Hey Glenn,

So i went ahead and made all 3 possible modes for you (see attached file).
All modes are present however they come with a note. for the 39ch. mode
you have to patch the 39ch. mode followed by 7, RGBW generic LED fixtures.
The Chimp doesnt support multiparameter fixtures. You'll need a work around.
patch 6 x 39ch. pixelblade 7's. then patch 6 x 7 = 42 RGBW fixtures. assuming you
want your function channel go ahead and patch 6 x the pixelblade 39ch. function fixture.
now patching comes down to correct selection order. In order to patch all fixtures at once
you need to do as followed.

for example
Pixelblade 7 39ch. mode FIX ID: 101 thru 106
RGBW LED FIX ID: 401 thru 442
Pixelblade 7 39ch. function FIX ID: 111 thru 116

this is your selection order syntax.
(1st fixture 101 + 401 -> 407 + 111) + (2nd fixture 102 + 408 ->414 + 112) +
(3rd fixture 103 + 414 -> 421 + 113) + and so on and so on.

after doing this for all 6 fixtures hit set and set your start adres. then everything should be
running.

Thans fot the quick response i will try it out