Chimp 100 Tour pack
Version 2.0.5
Off Dim FX arbeitet nicht in gespeicherten Cue 
Fixture Eurolight TMH-x4 im Zone Mode aus Chimp Bibliothek
Steps to reproduce
- ein Dim FX läuft auf den Geräten
- Geräte auswählen, im Programer auf Effekte gehen und Off DIM Effect wählen
- Effekt hört auf, dann dies in einen leeren Cue speichern und auf Exector legen
- Programmer clearen, FX läuft wieder
- Cue mit dem OFF FX starten aber DIM FX geht nicht aus
- das gleiche mit Bewegungen funktioniert jedoch wie es soll
LG Kai

Hey together,
i think i discovered a bug in the effect engine.
I tried to combine a Random Offset but it's not working.
Steps to reproduce:
Take an arbitrary selection of more than 2 fixtures.
Create a dimmer-effect type sine, buddys 2, offset random
Expected behaviour: the offset is random for the buddys
Visible: all fixtures are random without the influence of buddys.
Best regards
David

Lampy Fixture file for the Showtec Phantom 180 wash (14CH)

ps: make sure this file is copied in the folder: showtec\library\

Attached Files

  Showtec_Phantom180Wash(14CH).fixlib (Size: 1,65 KB / Downloads: 7)

As you can see in the video in the follow link ( https://drive.google.com/file/d/1JZxwttm...sp=sharing ) there is a bug while i'm trying to create an effect and replace the effect fixtures. 
Desk: Chimp 100G2 Tourpack
Software Version: 2.05
Step 1. Select Fixture (in my case is a multifixture)  
Step 2. Add a Dimmer Pulse Effect
Step 3. Deselect the 1st Module of multifixture
Step 4. Store the Selected fixtures into effect

now you will see that the first module is keeping the effect and dont release it even if you will clear the programmer. 
the only way to stop doing this is to reboot the console. 
i also tried to Restart User Interface ([Infinity] + [Open] + [S4]) but nothing changed.

Hey!

Is there a way to have two Monitors for the onPC Virtual Machine?

VMWare requires the installation of the VMWare tools to be able to get two monitors, but without root on the system that would be difficult to install.

Two monitors would be handy to have the Main Screen on one and the "physical" UI on the other.


Thanks!

Hi, I have a question
I have the Lampy 20
For a school

Have various lamps
1. Showtec Performer Fresnel 1500
2. Showtec ACT Profile 50ww
3. Showtec ACT PC 60 RGBW
4. Showtec ACT Fresnel 50 WW
5. Showtec PAR 18Q4
6. Beamz LCB 155 RGBWAUV

I created the fixture by myself because it was not in the fixture database
These 3 work´s
1. Showtec compact PAR 18Q4  
2. Showtec ACT Fresnel 50 ww
3. Showtec ACT Profiles 50 ww

Maybe someone has a fixture for the others
Lamps ??
1. Beamz LCB 155 RGBWAUV  (77 Channel Mode)
2. Showtec ACT PC 60 RGBW (11 Channel Mode )
3. Showtec Performer Fresnel 1500 (20 Channel mode )

I hope someone can help me
Best regards Sascha

Software Version: 2.0.5
OnPC / Chimp 100 / Chimp 300

Steps to reproduce

- Start a new Show
- Add and Patch a Futurelight EYE-7 HCL in Standard Mode
- Select the Fixture
- Go to Programming Screen
- In Programmer, select the Color Attribute Group
- Change to Color Faders
- Move Blue Fader up and down, then green Fader Up and Down, then Red Fader Up to 100%

Expected Behaviour: 
The Color Picker sets the Red Channel to 100%

Observed Behaviour:
The Color Picker sets the green channel to 100%

Additional Information:

Setting all RGB Faders to 100 % should output:

Red: 100%
Amber 0%
Lime: 0%
Green: 100%
Blue: 100% 

but it outputs

Red: 0%
Amber 100%
Lime: 0%
Green: 25%
Blue: 100%

Type desk: Chimp 300.G2

Software version: V2.0.5

Connected USB-device: None

Networked devices: None

Description: When changing the Default-values of a RGBW-Module in a Multi-fixture to 0 (Red/Green/Blue/White) the first channel is not changed (in this case RED)

Steps to reproduce: Patch an iM2515 or IFX640 and go to the Module-editor, in the editor select all the default values from the RGBW-module (they are on 255) and change them to 0.

The first channel stays on 255 and is not editable.


Expected behaviour: All the RGBW-Default values should change to the value given.


Observed behaviour: Only the first channel is not changed or editable in the RGBW-Module, this does not only relate to the Default
Values but also on the Highlight / DMX-max etc.

Noticed that this error is also in the 4 Channel Helix (the 6 Channel version works)

I would like to have the option to have an virtual Fader on the magic screen, so I can control cue lists like Fog Intensity or so without blocking an physical fader.

Hey,
 maybe is it possible to set the Masters to predefined Values? For example: My Speed Master is set to BPM mode and I will set him to 128 bpm by tap an executer. Maybe its possible to do it with the CMD feature.