Would be great to have a possibility to name the mutual release groups. And even greater would it be to be able to freely create additional mutual release groups!

When I have a cuelist with two cues I expected the run mode "Release at End" to behave like this:
Execute Cue 1 -> Press GO -> Execute Cue 2 -> Press GO -> Cuelist is released
instead it behaves like this: 
[color=#000000][size=medium][font=Times New Roman]Execute Cue 1 -> Press GO -> Execute Cue 2 -> Cuelist is released immediately[/font][/size][/color]
[size=medium]Seems to be wrong as the manual states: Release at End - The Cuelist will release (Switch off) itself after hitting go another time while the last cue is being output.[/size]

I tried to delete color presets 1-30 with the command DELETE PRESET 1 THRU 30 -> ENTER and although the console asked if I want to delete 30 presets, it does nothing after pressing OK.
Best regards,
Edi

I selected two RGBW PAR fixtures and set their RGBW values to the color RED.
Then I selected two other RGBW PAR fxitures and set their RGBW values to BLUE.
I recorded the above mentioned programmer content to an empty preset and named it RED PRESET.
As I mistakenly also recorded the two blue fixtures into that preset, I wanted to remove them from the preset.
So, with a cleared programmer I loaded the preset (LOAD + Preset), selected the two blue fixtures and pressed REC -> REMOVE -> PRESET.
I expected, that this would remove the values in the programmer from the preset, but instead it deleted the complete preset. 
As I tried to store a new preset on the place where the deleted one was, the suggested name reflected the  old name RED PRESET. So it seems, there is also something left in the background...
Am I wrong, that you should be able to remove specific content from a preset as you are for a cue?
Best regards,
Edi

Hey!
In my opinion it would be a great feature to have the ability to export the patch list of a show as a table (PDF/XLS/CSV) to a USB drive.
When I set the addresses of my fixtures on stage or while packing for the show, I often print out the patch list as a reference for quickly setting up my devices.
For now I have to write down every Fixture with its name (or in my case ID) and its DMX address and with a few dozen lamps this can take a while.
So yeah, having the option to export the list would make things easier.

Lampy 20, 2 universes

Software Version

1.03



External touch screen connected:

Yes



Midi USB device connected for receiving midi commands from a Raspberry Pi



Short description of the bug:
When the midi input is enabled and saved. After shutdown and opening the same show, midi input is disabled. So these show settings aren't saved with the show.



How to reproduce the bug

Enable midi input. Save the show and shutdown. Start the desk up again, open the show and look at the midi input. I did check several times, but it wasn't enabled.



What do you expect?
I expect the enabled midi input to be saved in the showfile.

It would be helpful when searching or sorting if there was the possibility in all overviews to be able to sort the overviews as .... e.g. Date (newest / oldest, name (ascending and descending), etc.
Es wäre hilfreich beim suchen oder sortieren wenn es in allen Übersichten die möglichkeit geben würde die Überichten  sortieren zu können als .... z.b. Datum ( neustes / ältestes , Name ( auf und absteigend )  , usw..

If you give a group a colored border, the border is automatically colored in the same color for all fixtures in the group in the fixture overview. (only if the fixture does not yet have a colored border.) This function should optionally be switched on or off in the settings, depending on how you work.
Wenn man einer Gruppe einen farbigen Rand gibt, das dann automatisch auch allen in der Gruppe enthaltende Fixtures in der Fixutre übersicht  der Rand in der selben Farbe eingefärbt wird. (nur  sofern das Fixture noch keinen farbigen Rand hat. ) Diese Funktion sollte wahlweise je nach Arbeitsweise in den Settings ein oder ausgeschaltet werden.

I would like several e.g. Presets (or cues .. or ...) can move. I.e. I mark several presets and move them in one go.

The overview in the fixture overview is very confusing because they are all packed one after the other. With many fixtures it quickly becomes obscure and you search for a long time if you don't know exactly which fixture number the fixture has. It would be great if you could place the fixtures freely like e.g. the groups in the group overview.