Hi there,
Though I'm pretty new on the Chimp and learning more every day, I found a little problem with I think is a Bug. While creating some, single cue, delay timing I wasn't able to alter the timing option in color cue's. Intensity, position, gobo etc, are working as expected.
Chimp 300 On PC
Software version 1.12External display connected, no touchscreen
No USB connected
Reproduce; Select Group - Select Colour preset, here the Timing function gets disabled.
I Work on windows 10, with VM Ware 16 (non commercial use)
However I could make mistakes I don't think I did in the syntax subscribed above.
Kind regards
Karel

Type of the Desk: Lampy 20 with dongle

Software Version: 1.01

Display Connected, is a touchscreen?: Yes, Dell P2418HT touchscreen

Connected USB Devices: keyboard and mouse

Networked Devices: connected to LAN, DHCP

Description: Fan options are indicated above the encoders, but cannot be set

Steps to reproduce:
- Select the Effects home screen
- Press the Fan button: the encoders now show fan options (like Grouping Fan, Direction Fan)

Observed Behavior:
If you have an effect set, parameters can be changed, but only by clicking the encoder and entering a value, not by turning the encoder. What you are changing are the effect parameters, however, not fan parameters.

Type of the Desk: Lampy 20 with dongle

Software Version: 1.01

External Display Connected, is a touchscreen?: Yes, Dell P2418HT touchscreen

Connected USB Devices: keyboard and mouse

Networked Devices: connected to LAN, DHCP

Description:
You cannot set fan for pan or tilt if you start from a position preset

Steps to reproduce:
- Select a few moving heads
- Select a position preset that includes pan and tilt values
- Press the fan button
- Select the Values home screen
- Now turn the Pan Fan encoder to fan the pan

Expected Behavior:
I would expect the pan to fan

Observed Behavior:
The pan does not fan initially. However, in the values screen, the tilt value changes from the preset to the raw value. If I then turn the Pan Fan encoder, the pan does fan. This bug only applies to the Pan Fan. If I change the Tilt Fan, it does work immediately.

Hallo Highlite Team,
 
Ich verwende ein Chimp 100g2 Touringpack mit Banana Wing und 2 Bildschirm.
Jetzt habe ich mir die neuste Software 1.12 beta aufgespielt und habe seitdem immer wieder Probleme mit dem 2. Bildschirm (external).
Wenn ich die Konsole hochfahre, hat der 2.Bildschirm (external) keine Calebrierung mehr.
Ich kann keine Buttens mehr genau berühren, der Zeiger reagiert dann immer weiter rechts. Erst nach erneutem aufspielen des updates 1.12 Beta ist das Problem dann weg.
Ebenso erkennt er dann auch, nicht immer, das Universum 3 u. 4 nicht.

Noch einmal etwas genauer erklärt:
[size=x-small]Ich schalte abends nach dem Programieren die Konsole aus (hat tagsüber alles funktioniert)[/size]
[size=x-small]Am nächsten morgen schalte ich die Konsole wieder ein und der zweite Bildschirm hat dann keine
[/size][size=x-small]Kalebrierung mehr, er lässt sich dann auch weder mit der Tastenkombination noch über den Bildschirm[/size]
[size=x-small]Kalebrieren.
[/size][size=x-small]Erst wenn man das update 1.12 beta erneut instaliert funkrioniert dann alles.
[/size][size=x-small]Auch wenn mann mal zwischewndurch rebootet passiert es mit der fehlenden kalibrierung.[/size]
[size=x-small]Ich hab mal Versuchsweise die HDMI Kabel der Bildschirme getauscht. Wenn man das macht geht der erste Bildschirm dann nicht.
[/size]
[size=x-small]Das mit den verlorenen Universen hab ich durch ein neues Kabel zwischen den konsolen behoben.[/size]
[size=x-small]Dürfte eigentlich nicht passieren, denn ich habe diese so erworben und sie ist erst knapp über ein Jahr alt.[/size]

type of the Desk : Chimp300G2
Software Version: 1,11
External Display Connected, is a touchscreen?: Yes (DELL or Netum = same issue)
Connected USB Devices: Yes external touchscreen

Description:
impossible to change preset type vue on the Chimp Screen when a touch screen is connected. Work on the external screen. 
When the external screen is disconnect it's working again.
I tried with using a mouse but same issue.

Additional Information
Please see this video: 

Hi,
i guess there is a new bug in the Fixture View in 1.12.
After renumbering Fixtures in the patch, so that they have a new order, the new order is not shown in the Fixture View.

Steps to reproduce:
- Patch 2 Fixtures with user number 1 and 2.
- Set the Fixture number of the first fixture from 1 to 3
- The new order of the fixtures is visible in the patch in order of the user numbers
- Go to a Fixture Window eg. Programming View
- The first item shows user number 3, the second user number 2 -> order not correct
-After reloading the show / rebooting the console the correct order of the Fixtures is updated in fixture view

Regards David

hi, I've found extremely helpful various selection modes.Is possible to implement it ,in order to be able working with matrix selection? (yes, something like MAtricks )

Type of the Desk: Chimp 100 & Chimp PC

Software Version: V1.12

External Display Connected, is a touchscreen?: Yes

Connected USB Devices: Touch Screen

Networked Devices: No

Description:
I have found an error when selecting the "Deactivate" option of a parameter. Error message appears (Server Connection Lost)

Attached Files

Thumbnail(s)
   

Hi,
Would it be possible to open a little Confirmation dialog by clicking on the "save cuelist settings as default" button? Then you would have a little feedback if it worked and could deny it if it was an accident

Regards David

In V1.12 you added the ability to click on the label of a fader or executor on the screen to open a new window to edit the settings of the fader or excecutor and a get a view and the settings of the cuelist.
It would be really nice if this window opens up in the cuelist table in programming, quadsplit and co., too. At the moment it only selects the cuelist. Then you could easily edit the settings with no need to change to a cuelist view window. Only the option of executor settings would not be needed.

Regards David