When you use a factory fixture, and you want to change (default) somthing, you have to programm the whole movinghead again (fixtures, color, beam, prism, position etc.) It would be so cool if we can change the fixture without programming the whole movinghead again....

Post body:

Type of the Desk: LAMPY 20

Software Version: 1.01

External Display Connected, is a touchscreen?: no

Connected USB Devices: none

Networked Devices: none

Description:

While patching my ETC Lustr 2 I noticed that it doesn't show the correct channel mode description. It seems like instead it shows the raw format in whatever format the fixture library is written in. 

Steps to reproduce:

Go to patch -> manufacturer library -> ETC -> Source Four LED Lustr 2 and look at the channel mode selection on the right.


Expected Behavior:

A readable selection of the available modes

Observed Behavior:

A rather cryptic selection of the available modes

Additional Information

I don't know if this is a restriction of the board (which would be a real shame and could be the killer for me) but the ETC Source Four LED Lustr 2 has an extra +7 channel mode that can be selected on top of any of the available DMX modes. [color=#000000][size=medium][font=Times New Roman]Essentially it's a direct colo[/font][/size][/color][color=#000000][size=medium][font=Times New Roman]r control instead of simulated RGB access. [/font][/size][/color]

This mode doesn't show while patching but would be great to have.

Post body:

Type of the Desk: LAMPY 20

Software Version: 1.01

External Display Connected, is a touchscreen?: no

Connected USB Devices: none

Networked Devices: switch and router / directly on router

Description:

After the first start I wanted to check for updates and tried to get the board connected to the internet.
I tried DHCP as  well as manual IP, had it on a unmanaged switch that is going to my router and even on the router directly. No luck.
It always says no connection, check cable (I tried two different cables, both work on my workstation)

Steps to reproduce:

Connect ethernet cable, try to online update software or fixture library


Expected Behavior:

A server connection

Observed Behavior:

No server connection

Additional Information

Post body:

Type of the Desk: LAMPY 20

Software Version: 1.01

External Display Connected, is a touchscreen?: no

Connected USB Devices: none

Networked Devices: none

Description:

When playing around with the board I turned off shutter in the cog wheel menu of my Cameo FC2s and the Software crashed. I had to cut the power to bring it back.

Steps to reproduce:

Go to Values, shutter and disable shutter.

Expected Behavior:

Not sure, but not a crash.

Observed Behavior:

Software crashes and freezes.

Additional Information

It's a fresh blank show file with 3 fixtures, no groups, no nothing.

Hi there,
Running a Chimp 300.G2 (version 1.12) I ran into a problem with the AtlaBase Library for the Infinity IW 741.
When select 1 or more fixtures the 'Control' section gets greyed out.
Funny thing about this is that, when I import the fixture file provided by Highlite (when I was running the desk in version 1.11) it all works fine. So it looks like there's a problem with the AtlaBase Library.
Kind Regards
Karel

Infinity Key Funktionen:

Infinity + Temp = Opens Page Directory

Infinity + Open + S1 = Calibrate Internal Screen
Infinity + Open + S2 = Calibrate Secondary Screen
Infinity + Open + S4 = Restart User Interface

Infinity + Skip = Skip Backwards (In Selected Cuelist)
Infinity + Open = Closes all Dialog Windows
Infinity + Select = Clears current Selection
Infinity + Off = Releases all Cuelists
Infinity + Fpg+ = Sets Fader Page to 1
Infinity + EPg+ = Sets Executor Page to 1

Infinity + Highlight = Toggles Solo
Infinity + Clear = Brings back the last programmer content from before clearing
Infinity + Load = Loads all Output for currently selected fixtures
Infinity + Prev = Selects all fixtures with values in programmer
Infinity + Next = Selects all fixtures from original selection set
Infinity + Encoder Turn = Sets Fine Values for this Attribute

Infinity + Edit + Fader Go / Pause Button = Opens the Settings Tab for the Cuelist on the Playback Page 
Infinity + Edit + Executor Button = Opens the Settings Tab for the Cuelist on the Playback Page 

Infinity + Cuelist Item in Cuelist Pool: Deselects the Cuelist
Infinity + Preset Item in Preset Pool: Loads the Presets Values for selected fixtures instead of a reference to the preset.

If Scroll is shown for an encoder:
Infinity + Encoder Button will scroll to bottom
Encoder Button only will scroll to top

Tables:
Infinity (Or Shift on Keyboard) + Clicking in a Multiselect Table will select multiple Cells
Infinity (Or Shift on Keyboard + Arrow Keys on Keyboard will allow to make a multi selection

Toolbars:

Selection Toolbar:
Infinity + All = Selects all fixtures with values in programmer

Off Toolbar:
Infinity + Reset Group Master Button = Resets all Groupmasters to 100% without asking for confirmation
Infinity + Reset Cuelist Fader Button = Resets all Groupmasters to 100% without asking for confirmation
Infinity + Off All Playbacks Button =  Offs all Cuelists without asking for confirmation
Infinity + Release Everything = Resets / Offs EVERYTHING without asking for confirmation

Dialogs:

Shutdown / Reboot Dialog:
Infinity + Reboot Button in Dialog = Quit / Restart Application Only
Infinity + Shutdown Button in Dialog = Quit / Restart Application Only

Fixture Library Editors:

Add Multiple Ranges Dialog:
Infinity will show all values in 16bit

Add or Edit Ranges Dialog:
Infinity will show all values in 16bit

Module Channel Editor:
Infinity will show all values in 16bit

Output View:
Infinity will show all values in 16bit

MagicSheets:
Infinity during Rectangle Selection: Selection will be inverted

We have identified an issue in the software where files can not be imported again if they have been renamed after export.

As a workaround either set the name directly in the software prior to exporting, or if you have a file that was exported earlier where import fails:

Copy the file to another folder on the computer.
Rename the copy's file ending to .tgz
Unpack the .tgz using a Compression Utility such as archiver in MacOS or WinRar in Windows.
This will create a new folder named after the file. Open this folder. In the folder you'll find a .lib or .show file, copy and paste the name before the .lib or .show file ending.
Rename the file on the stick to this name.
Import again.

We have entered the issue into our issue tracking system, but no ETA on when this will be fixed yet.

Sorry for any inconveniences,

Denis

Hello everybody,

I got my Lampy 40 last week.
Unfortunately I have to find out that some fixtures don't work,
For us it concerns the following fixtures:

Stairville CLB 4 in 14 channel mode (included in 7 channel mode) we need 14 channel mode,

Cameo MultiPar COB 1 17 channel mode

lightmaXX VEGA HALO 90

Varytec Hero Spot 90

The Atlabase database contains you.
Please improve there.

We bought the Lampy 40 2 U because the advertising promised a lot and we wanted to get away from a PC version that kept crashing.
Basically the Lampy 40 is great, but if our fixtures don't work in the Lampy, then the desk is not an alternative for us and we have to return it.

A Chimp 100 is just not in our budget, we are a small band and 2500 € for a lighting desk is quite a number.
Could you realize that these fixtures are available in the Lampy 40?

Thank you
Unfortunately, my English is not that good and I had it translated with Google Translator

Running Chimp 100 V1.12 beta with one touchscreen connected and two dmx outputs in use.

When i try to fan my P/T position it only work when there are values in the programmer. Most of the time i make a base position (straight forward) and from there on i make my other preset positions. But when i want to use the fanning option nothing happens.

The name from the preset will appear in the programmer and then i cannot use the fanning options.
But when there are just values in the programmer the fanning works just fine.

This is also happening on the OnPc version that i use at home.

Hope this will be checked 

Best Regards,
Tom

Good day everybody,
I am a freshly baked new Chimp 100 Tourpack user or am also new to the forum But I have a question right away and I hope you can help me.

I would like to explain it using the example.
I have several cues (moves or positions) on a fader and let's assume the active cue is currently cue 1. Now I would like to use a button to preselect cue 4, for example, but this shouldn't be directly switch over when skiing through, only with a "GO" command it should then pass from cue 1 to cue 4. I hope I was able to explain it well. If it is a simple solution, I ask for your indulgence as I am still learning. Since I was a pure DasLight user before. Is there such a function or could you add such a function to the wish list?

thank you in advance
Kind regards
Patrick
------------------------------------------------------------------------------------------------------------------------------

Guten Tag zusammen,
ich bin frischgebackener neuer Chimp 100 Tourpack User bzw. bin auch neu im Forum
Hab da aber gleich mal eine Frage und ich hoffe Ihr könnt mir helfen.

Ich möchte es gern am Beispiel erklären.
Ich habe mehre Cues (Moves oder Positions) auf einem Fader liegen und wir nehmen mal an der aktive Cue ist gerade der Cue 1. Jetzt würde ich mir gerne über einen Button als nächstes zum Beispiel den  Cue 4 vorwählen, aber dieser soll noch nicht direkt umschalten beim durchskipen, erst durch einen Befehl "GO" soll dieser dann von Cue 1 auf Cue 4 überfaden.

Ich hoffe ich konnte es gut erklären, sollte es eine einfache Lösung sein, bitte ich um Nachsicht da ich noch im Lernprozess bin. Da ich vorher reiner DasLight User war.
Gibt es so eine Funktion oder könntet ihr so eine Funktion mit auf die Wunschliste aufnehmen?

Danke vorab

MFG
Patrick